
Deflex
A new look at Deflex M10XR thermoplastic materials
Dental technicians who manufacture flexible dentures already have their proven materials and work technologies that guarantee good results. However, they invariably struggle with problems resulting from the physicochemical characteristics of thermoplastic materials. At the end of 2015, a new thermoplastic material Deflex M10XR appeared on our market and there are many indications that this is an opportunity to solve several problems with performing these works.
One of the most common disadvantages when working with thermoplastic materials is their thermal shrinkage. It requires strict adherence to the specified thickness of the denture plate, which limits the design freedom. With too coarsely modeled elements, high material shrinkage results in the work mismatching the model. It is an irreversible error and it is practically impossible to correct. The Deflex M10XR has much less stringent requirements. Its minimal contraction (0.3%) significantly reduces the risk of mismatching the prosthetic restoration. There are also no thinning inside the prosthesis, so characteristic of too thick nylon or acetal plates. We work on any class IV plaster, and the accuracy of fitting is so great that even extensive dentures adhere well to the base. Thermoplastic materials based on polyamide and acetal, unfortunately, cannot be easily repaired. They do not combine chemically with acrylic, and the possible supplementation of nylon dentures with "extra injection" is very time-consuming and expensive. There are also methods of joining with adhesives, but ultimately, as a result of differences in the flexibility of the bonding and the bonded material, the materials delaminate and penetrate into the sediment spaces.
The new Deflex M10XR material stands out from traditional thermoplastics because it is polymer-based and has a high ability to chemically bond to acrylics when the material's surface is activated with monomer. This process requires no special bonds or procedures. It is enough to moisten the surface with monomer and apply the material, just like in the case of repairing classic acrylic dentures. This combination is effective, takes much less time and does not cause additional costs. This results in the following advantages: - easy and inexpensive repair of the denture, - the possibility of relining the denture, - the possibility of sticking the teeth into the denture shaft, - the possibility of inserting acrylic teeth into denture in a very limited space, when the artificial teeth must be very short or narrow. It is worth mentioning the aesthetic qualities of Deflex materials. Against this background, it looks very favorable. It looks like nylon, it is available in transparent and pink colors based on transparent. The so-called the chameleon effect masks it well in the patient's mouth. Its stiffness is similar to acetal. It is easy to work with, and when processed with a cutter, it "threads" much less than nylon. After polishing, it obtains a high gloss, similar to acrylic.
After years of presence on the market of nylon materials (polyamides) and acetals, apart from their undoubted advantages, some weaknesses have also emerged. The new thermoplastic material Deflex M10XR introduces a new quality and gives new possibilities of making prostheses, therefore it is a good alternative to existing solutions and extends the offer with works that have not been possible so far.
* Deflex - MAD 1300 injection molding machine
Characteristic:
The MAD1300 injection molding machine from Deflex is the newest injection molding machine for thermoplastic dentures. The fully open device (any material available on the market can be used in it) has an innovative super-strong pneumatic piston that allows for injection of even the most demanding materials. The Deflex company has been specializing in the production of materials and devices related to dental technology for 15 years. Thanks to the accumulated experience, the MAD1300 injection molding machine is the best adapted device available on the market: it is characterized by easy operation, failure-free operation and efficient use of compressed air - thanks to which, even with the use of a small amount of compressed air, we obtain a high injection force.
Deflex MAD1300 injection molding machine is:
- maximum time savings
- fully automatic
- pre-defined and empty programs
- easy ...
Acrilato - injection acrylic without residual monomer - cartridge 32.6 g
Application:
Complete dentures
Features:
Prostheses made of Acrilato fd material are more resistant to mechanical damage and lighter than those made of conventional acrylic.
- They are completely devoid of residual monomer.
- The contraction during polymerization at the level of 0.3% guarantees a perfect fit of the denture in the patient's mouth.
- The material is chemically bonded with traditional "cold" acrylics, which allows for its repair or relining in a simple and quick way.
It does not cause allergies.
Package:
Tube: 32.6g
...Deflex - Classic L - 32.6g diameter 22mm - complete dentures + large partial
Semi-hard polyamide for thermal injection.
Application:
All partial dentures.
Features:
Natural polyamide is perfect for all types of removable partial restorations, even with thin clamps. Compared to traditional "soft nylons", the material is distinguished by high hardness while maintaining adequate flexibility in the retention areas where it is necessary for the proper functioning of the restoration. Reduced fluid absorption makes it easier to maintain hygiene in the denture. It does not cause allergies.
Available in colors:
- Banner
- Soft Pink - slightly veined pink transparent
- Intense pink - intensely pink veined
Packed in a tube protecting against harmful external factors (moisture, sunlight).
Package:
Tube: 32.6 g
...Deflex - Classic M - 23.2g, diameter 22mm - partial dentures
Characteristic:
Semi-hard polyamide for thermal injection.
Application:
All partial dentures.
Features:
Natural polyamide is perfect for all types of removable partial restorations, even with thin clamps. Compared to traditional "soft nylons", the material is distinguished by high hardness while maintaining adequate flexibility in the retention areas where it is necessary for the proper functioning of the restoration. Reduced fluid absorption makes it easier to maintain hygiene in the denture. It does not cause allergies.
Available in colors:
- Banner
- Soft Pink - slightly veined pink transparent
- Intense pink - intensely pink veined
Packed in a tube protecting against harmful external factors (moisture, sunlight).
Package:
Tube: 23.2g
...Deflex - Classic S - 14.9g, diameter 22mm - repairs - touching the buckle
Characteristic:
Semi-hard polyamide for thermal injection.
Application:
All partial dentures.
Features:
Natural polyamide is perfect for all types of removable partial restorations, even with thin clamps. Compared to traditional "soft nylons", the material is distinguished by high hardness while maintaining adequate flexibility in the retention areas where it is necessary for the proper functioning of the restoration. Reduced fluid absorption makes it easier to maintain hygiene in the denture. It does not cause allergies.
Available in colors:
- Banner
- Soft Pink - slightly veined pink transparent
- Intense pink - intensely pink veined
Packed in a tube protecting against harmful external factors (moisture, sunlight).
Package:
Tube: 14.9g
...Deflex - M10 XR - L 32.6g diameter 22mm - complete dentures + large partial
Modern polymer-based thermoplastic material for universal use. Flexible with increased hardness compared to other thermoplastic materials. Low contraction (0.6%) guarantees a good fit of the denture. It is chemically combined with traditional "cold" acrylic, so that the material can be repaired and relined in a traditional way.
Application:
- Complete dentures,
- partial dentures with supports,
- overdenture dentures,
- partial dentures on clasps
The colors of the Deflex materials are a combination of translucency and shades of pink which enable the effect of "adaptation" of the prosthesis to the natural color of the patient's teeth and gums. These effects only become visible when you place the work in your mouth.
Features:
- Does not contain residual monomer. Very easy to polish to "high gloss".
- Thanks to its stiffness and fractu ...
Deflex - M10 XR - M 23.2g diameter 22mm - partial dentures
Characteristic:
Modern polymer-based thermoplastic material for universal use. Flexible with increased hardness compared to other thermoplastic materials. Low contraction (0.6%) guarantees a good fit of the denture. It is chemically combined with traditional "cold" acrylic, so that the material can be repaired and relined in a traditional way.
Application:
Complete dentures, partial dentures with supports, overdentures, partial dentures with latches
The colors of the Deflex materials are a combination of translucency and shades of pink which enable the effect of "adaptation" of the prosthesis to the natural color of the patient's teeth and gums. These effects only become visible when you place the work in your mouth.
Features:
Does not contain residual monomer. Very easy to polish to "high gloss". Thanks to its stiffness and fracture resistance, it al
...Deflex - M10 XR - S 14.9g diameter 22mm - repairs - touching the buckle
Characteristic:
Modern polymer-based thermoplastic material for universal use. Flexible with increased hardness compared to other thermoplastic materials. Low contraction (0.6%) guarantees a good fit of the denture. It is chemically combined with traditional "cold" acrylic, so that the material can be repaired and relined in a traditional way.
Application:
Complete dentures, partial dentures with supports, overdentures, partial dentures with latches
The colors of the Deflex materials are a combination of translucency and shades of pink which enable the effect of "adaptation" of the prosthesis to the natural color of the patient's teeth and gums. These effects only become visible when you place the work in your mouth.
Features:
- Does not contain residual monomer. Very easy to polish to "high gloss".
- Thanks to its stiffness and fracture re ...
Deflex - PEEK Ossis set of rings for frameworks Promotion
Biocompatible PEEK Ossis material for injection.
A set of rings enabling the injection of material on the frameworks (crowns, bridges). The material should be veneered with composite.
Package:
- 4 casting rings (different sizes)
- Ring cover
- A stand for rings attaching the socket to the injection molding machine.
Deflex Acetal 100g (8 cubes)
Deflex Acetal - is a non-toxic material and does not cause allergies.
It is a suitable replacement for acrylic resin and metal in many prosthetic works. Possible to work without expansion plaster.
Acetal application:
- aesthetic buckles for dentures, the so-called skeletal,
- partial dentures,
- bridges and bridges for telescopes,
- prosthetic elements on implants,
- bite and stabilizing splints,
- retention elements on the beams which are also reinforcement.
Injection temperature - 245 degrees C (+/- 5C) Material melting time - 15min Injection and heating - 30-60 seconds Cooling time under constant pressure - 30 minutes Working pressure - 5.0-7.0 Bar
Package:
8 cubes, min 100g.
...Deflex box - for the MAD1300 injection molding machine
Can for injection of thermoplastic materials - compatible with the Deflex MAD1300 injection molding machine. Durable and solid construction.
Package:
1 piece
...Deflex PEEK OSSIS granules for injection, beige color 20g Promotion
The manual is available in the DOWNLOAD section on www. mikran.pl Injection granules, beige color.
The biocompatible PEEK OSSIS injection material is ideal for:
- individual connectors
- structures of crowns and bridges (1- 2 spans)
- anatomical structures of crowns and bridges
- Maryland bridges
- telescopic crowns
- constructions of beams for overdentures
- hybrid dentures
- other implantoprosthetic works
- removable dentures.
The material can be used to work on a deflex injection molding machine and other devices operating at a temperature of 390 ° C.
PEEK OSSIS removable dentures are made in the traditional canning method (such as acetal), while permanent restorations are made using a special set of rings (adapted only to the Deflex device) and an investment material.
Package:
20 g
...Deflex PEEK OSSIS injection granules pink color 20g Promotion
The manual is available in the DOWNLOAD section on www. mikran.pl Injection granules, pink color.
The biocompatible PEEK OSSIS injection material is ideal for:
- individual connectors
- structures of crowns and bridges (1- 2 spans)
- anatomical structures of crowns and bridges
- Maryland bridges
- telescopic crowns
- constructions of beams for overdentures
- hybrid dentures
- other implantoprosthetic works
- removable dentures.
The material can be used to work on a deflex injection molding machine and other devices operating at a temperature of 390 ° C.
PEEK OSSIS removable dentures are made in the traditional canning method (such as acetal), while permanent restorations are made using a special set of rings (adapted only to the Deflex device) and an investment material.
Package:
20 g
...MaxiFresh cleaning tablets 24 pcs.
MaxiFresh cleaning tablets
For professional and home cleaning and care of bleaching splints, retainers, relaxation splints, bruxism splints and sports splints. It is perfect for cleaning all thermoplastic materials and trainers.
Advantages:
- It reduces discoloration
- Refreshes the surface and eliminates unpleasant odors
- Saves material as it does not contain abrasives
- Increased service life of the tooth rail with daily cleaning.
Use:
Place the Maxi-Fresh cleaning tablet in a vessel filled with 150 ml of water at approx. 37C. (Colder water may take longer to dissolve the tablet). After the tablet has completely dissolved, place the rail in the vessel for a minimum of 45 minutes. After the cleaning process is finished, rinse the rail under running water and dry the surface.
Package:
24 pcs.
...Silicone spray for injection molding machines
Silicone spray to lubricate the cartridge prior to insertion into the injection molding machine. Reduces friction during injection.
Packaging: 400 ml
...Tubes 22mm with a stopper - Deflex
Empty tubes with stopper for injection of thermoplastic materials. Diameter 22mm. Thanks to them, you can pack the material yourself. Compatible with the MAD1300 injection molding machine
Package:
1pc tube 1pc cork
...Unitrim stone for thermoplastics / acetal large EVE
Highly abrasive stone which, thanks to its porous structure, does not heat up the thermoplastic material during processing, reducing the risk of material deformation. Use the stone for pre-treatment - collecting material. (use 3000-5000 rpm optimally / max 20,000 rpm)
Package :
1 piece.
...Unitrim stone for thermoplastics / acetal small
Characteristic:
Highly abrasive stone which, thanks to its porous structure, does not heat up the thermoplastic material during processing, reducing the risk of material deformation. Use the stone for pre-treatment - collecting material. (use 3000-5000 rpm optimally / max 20,000 rpm)
Package :
1 piece.
...